Plant tents & equipment 6 min read

Which LED for which tent size? Watts, µmol and distance

How many watts and how much light does your tent need? With the calculation, a table from 60×60 to 150×150 cm, hanging height and electricity costs – plus suitable LEDs from our range.

What matters is not the wattage on the box but how much usable light the lamp emits (PPF in µmol/s) and how much of it reaches the canopy (PPFD in µmol/m²/s). As a rule of thumb, flowering needs around 700 to 1,000 µmol/s per square metre of tent area, vegetative growth about 400 to 600. With a good full-spectrum LED at 2.7 to 3.0 µmol/J, that means about 250 to 360 watts of actual power draw per square metre for flowering – for example around 90 to 130 W for a 60×60 tent and 360 to 510 W for a 120×120 tent.

Why does the wattage alone say little?

The wattage only describes how much electricity the lamp uses, not how much of the light plants can use. Two 200 W lamps can emit very different amounts of light depending on chips, driver and design. On top of that, some lamps carry a fantasy figure in their name ("1000 W") but draw only a fraction of it from the socket. What counts is always the actual power draw according to the data sheet.

Three values help with comparison:

  • PPF (µmol/s): the total amount of plant-usable light the lamp emits per second.
  • Efficiency (µmol/J): how much light comes out per watt. Good full-spectrum LEDs are at about 2.5 to 3.0 µmol/J, very efficient models above that.
  • PPFD (µmol/m²/s): how much light reaches a given spot on the plant surface. This depends on the lamp, distance and tent walls.

A common mistake is to confuse PPF and PPFD: the PPF is on the data sheet and is fixed, the PPFD is measured in the tent and changes with every centimetre of distance.

How much light does each phase need?

Young plants need much less light than mature ones. The following guide values for the light at the top of the plant are common in grow guides for artificial light; the sources are listed below. Values may differ for individual species.

PhasePPFD (µmol/m²/s)Light per day
Germination and seedlings100 to 30018 hours light, 6 hours dark
Vegetative growth400 to 60018 hours light, 6 hours dark
Transition to flowering500 to 70012 hours light, 12 hours dark
Flowering700 to 1,00012 hours light, 12 hours dark

Whether a plant needs shorter days to flower depends on the species. Many species respond to the switch from 18 to 12 hours of light, others flower regardless of day length. Increase the light for young plants in small steps of about 25 to 50 µmol/m²/s and watch the plants for a day or two before adjusting further.

Which power suits which tent size?

Multiply the area of your tent by the target PPFD to get the light output the lamp should deliver at minimum. Divide this value by the efficiency to get the required power draw. Some light is lost at the edges and walls, so plan towards the upper end and dim if needed.

Tent sizeAreaLight output for growthLight output for floweringPower at 2.8 µmol/J (flowering)Examples from our shop
60 × 60 cm0.36 m²approx. 145 to 215 µmol/sapprox. 250 to 360 µmol/sapprox. 90 to 130 WMedic Grow MINI SUN-2 150W (420 µmol/s), Secret Jardin Power Pack 125W (390 µmol/s)
80 × 80 cm0.64 m²approx. 255 to 385 µmol/sapprox. 450 to 640 µmol/sapprox. 160 to 230 WMedic Grow MINI SUN-2 240W (672 µmol/s), Secret Jardin Power Pack 250W (778 µmol/s)
120 × 60 cm0.72 m²approx. 290 to 430 µmol/sapprox. 500 to 720 µmol/sapprox. 180 to 260 WLumatek ATS300W PRO (816 µmol/s), Treegers GL300W (825 µmol/s)
100 × 100 cm1.00 m²approx. 400 to 600 µmol/sapprox. 700 to 1,000 µmol/sapprox. 250 to 360 WMedic Grow MINI SUN-2 320PLUS (960 µmol/s), Lumatek ZEUS 300W PRO 3.1 (965 µmol/s)
120 × 120 cm1.44 m²approx. 575 to 865 µmol/sapprox. 1,010 to 1,440 µmol/sapprox. 360 to 510 WM400 Boxy (1,238 µmol/s), Treegers GL420W (1,155 µmol/s)
150 × 150 cm2.25 m²approx. 900 to 1,350 µmol/sapprox. 1,575 to 2,250 µmol/sapprox. 560 to 800 WLumen King Eco Line 720W V2 (1,944 µmol/s), 720 MultiSpec (1,891 µmol/s)

The ranges are our own rough calculation of PPFD guide value times area, without losses at the edges. The PPF values of the example lamps come from the manufacturer specifications on our product pages. A slightly stronger lamp is no problem as long as it is dimmable: you turn it down in the early phases and have reserves for flowering.

For rectangular tents such as 120×60 cm, an elongated lamp or two smaller lamps side by side usually give more even coverage than one square lamp in the middle. Check the coverage area stated on the data sheet.

How high do I hang the LED?

Follow the manufacturer's height recommendations first and start rather too high than too low. As a rough guide, full-spectrum LEDs are hung about 30 to 50 cm above the plant tops for young plants and 40 to 60 cm during vegetative growth. Many lamps are dimmable, so you can set the amount of light with the dimmer instead of constantly changing the height.

The inverse square law shows how strongly distance matters: double the distance means roughly a quarter of the light. If about 1,000 µmol/m²/s arrive at 30 cm, only around 250 remain at 60 cm. Even 10 cm make a noticeable difference.

If you want to know exactly, measure with a PAR meter at the height of the shoot tips, with the sensor level and facing the lamp. Do not measure only in the middle but also at the four edges, as it is often noticeably darker there. A lux meter such as the Milwaukee MW700 PRO is useful for comparing spots and distances; however, lux can only be roughly converted into PPFD, and phone apps are an estimate at best.

What does it cost to run an LED?

You calculate electricity costs as power draw times hours times electricity price. A 200 W LED uses 3.6 kWh per day at 18 hours of light and 2.4 kWh at 12 hours. At an example price of €0.35 per kWh, that is around €1.26 or €0.84 per day, i.e. about €38 or €25 per month. Your own tariff is on your electricity bill.

Because a more efficient lamp needs less electricity for the same amount of light, it is worth looking at the µmol/J figure when comparing prices too: a difference of 2.7 versus 3.0 µmol/J saves around a tenth of the electricity for the same light output.

Common mistakes: what often goes wrong with lighting?

  • Bought by the watts in the name: The model name is not the power draw. Compare watts from the socket, PPF and µmol/J.
  • Too little light: The plants grow long and thin and stretch towards the lamp. Hang the lamp lower or dim it up.
  • Too much or too close: Leaves bleach, curl or get pale spots. Hang the lamp higher or dim it down, especially for young plants.
  • Measured only in the middle: The edges often get much less light. Measure at several points.
  • Heat underestimated: LEDs also produce heat. Keep an eye on the temperature at leaf level with a thermometer/hygrometer with two measuring points and size the exhaust accordingly.
  • Several things changed at once: Adjust the height or dimmer first, then observe for one or two days.
  • Thinking 24 hours of light is faster: Plants need dark periods; continuous light is not standard.

In our shop at Lorenzstraße 9 in Hof, several LEDs are running on display, and we will work out with you which lamp suits your tent. You will find all lights online under LED lighting, hangers and timers under Lighting accessories and suitable tents under Grow tents.

Featured in this guide

Frequently asked questions

Is a 150 W LED enough for an 80×80 tent?

For seedlings and vegetative growth usually yes, for flowering it is rather tight. An 80×80 tent has 0.64 m², and for flowering around 450 to 640 µmol/s make sense. A good 150 W LED delivers about 400 to 450 µmol/s. For flowering, a lamp with 200 to 250 W of actual power draw is a better fit.

What is the difference between PPF and PPFD?

PPF states how much plant-usable light the lamp emits in total per second (µmol/s) and is listed on the data sheet. PPFD tells you how much of it reaches a given spot on the plant (µmol/m²/s). It depends on distance, position and the tent walls and is measured inside the tent.

Why is my lamp called “1000 W” but draws much less power?

Some manufacturers use a comparison or fantasy figure in the product name. What counts is the actual power draw according to the data sheet, i.e. the watts taken from the socket. Only with that figure and the PPF can you compare lamps fairly.

Can I simply dim the lamp instead of hanging it higher?

Yes, with dimmable LEDs this is often the better solution. You adjust the amount of light without changing the light distribution. Just make sure the lamp does not hang so low that the leaves get too warm.

How many hours of light do plants in a tent need?

For seedlings and vegetative growth, 18 hours of light and 6 hours of darkness are common; for flowering, many species use 12 hours on and 12 hours off. Continuous light is not standard. A timer ensures fixed times.

Sources

All information to the best of our knowledge and based on manufacturer data as of the date shown. It does not replace the manufacturer’s instructions. This guide was created with AI assistance and reviewed by our team.

More from Plant tents & equipment