Plant tents & equipment 6 min read

Sizing exhaust fans and carbon filters correctly

How many m³/h does your tent need, how big must the filter be and how do you set up the exhaust correctly? With the calculation, a table from 60×60 to 150×150 cm and climate guide values.

The exhaust should completely replace the air in the tent several times per hour. On paper, 20 to 30 air changes per hour are enough, i.e. tent volume times 20 to 30. In practice, however, the fan is chosen much larger because the carbon filter, ducting and bends slow it down and the lamp adds heat: a practical value of about 200 to 250 m³/h per square metre of floor area applies. The carbon filter should handle at least as much air as the fan and sits in front of the fan so that the fan pulls the air through the filter. You then set the fan to the right level with a speed controller.

Why does a tent need exhaust at all?

In a closed tent, heat from the lamp and moisture from evaporation build up. Without air exchange, temperature and humidity rise and corners with stagnant, humid air form. This favours mould and pests. The exhaust removes the warm, humid air at the top while fresh air flows in at the bottom. The carbon filter binds odours before the air leaves the tent.

How many m³/h does my fan need?

First calculate the tent volume: width times depth times height in metres. Multiplied by 20 to 30, this gives the pure calculated requirement. To choose the fan, use the practical value of about 200 to 250 m³/h per square metre of floor area, because the filter, ducting and heat cost performance. With a speed controller, you turn the fan down to what you really need.

TentVolumeCalculated requirement (20–30 changes/h)Practical value (200–250 m³/h per m²)Suitable from our shop
60 × 60 × 160 cm0.58 m³approx. 12 to 17 m³/happrox. 70 to 90 m³/hExhaust kit 100 mm, 360 m³/h, turned down
80 × 80 × 180 cm1.15 m³approx. 23 to 35 m³/happrox. 130 to 160 m³/hExhaust kit 100 mm, 360 m³/h
120 × 60 × 180 cm1.30 m³approx. 26 to 39 m³/happrox. 145 to 180 m³/hExhaust kit 100 mm, 360 m³/h
100 × 100 × 200 cm2.00 m³approx. 40 to 60 m³/happrox. 200 to 250 m³/h100 mm, 360 m³/h or Prima Klima set PK125
120 × 120 × 200 cm2.88 m³approx. 58 to 86 m³/happrox. 290 to 360 m³/hExhaust kit 150 mm, 680 m³/h
150 × 150 × 200 cm4.50 m³approx. 90 to 135 m³/happrox. 450 to 560 m³/hExhaust kit 150 mm, 680 m³/h

The calculated requirement and the practical value are far apart, and that is not a mistake. The calculated requirement describes the pure air exchange in an empty tent. The practical value includes the reserve for the resistance of filter and ducting, for the heat of the lamp and for warm summer days. In addition, fan ratings usually apply without filter and ducting; with both, a fan moves noticeably less air.

A generously sized fan with speed control is therefore the safer choice than one that is only just enough at full speed: it runs more quietly when turned down and has reserves when it gets warm.

How big does the carbon filter need to be?

The filter should handle at least the air volume the fan moves, ideally a little more. If the filter is too small, it slows the fan down, and the air flows through the carbon so fast that odours are not fully bound. Also make sure the flange diameters of filter and fan match or use a suitable adapter.

In our complete exhaust kits, fan, filter and ducting already match, so you do not have to put anything together yourself.

How do I set up the exhaust correctly?

The exhaust belongs at the top, because that is where the warm air collects. Fresh air comes in at the bottom on the opposite side.

  1. Hang the filter at the top of the tent: Attach it to the tent pole with light hangers or straps, with the opening facing the fan.
  2. Place the fan behind the filter: The fan pulls the air through the filter. This keeps the housing clean and the filter works evenly.
  3. Keep ducting short and straight: Keep the duct as short as possible and avoid kinks and unnecessary bends. Every metre and every bend costs performance.
  4. Lead the exhaust outside: Through the upper tent opening, sealed tightly with hose clamps.
  5. Open the intake at the bottom: For small tents up to about one square metre, the passive openings with insect mesh are usually enough. Larger setups get their own intake fan.
  6. Set the speed: Adjust the fan so that temperature and humidity stay within the target range. If the tent pulls slightly inwards, the exhaust is stronger than the intake – a slight negative pressure ensures that air and odours do not escape through gaps.

You also need a circulation fan: it moves the air inside the tent and prevents pockets of heat and humidity. For a tent up to about one square metre, an oscillating clip fan with a 15 to 20 cm diameter is enough. Do not point it directly at the plants; several small fans are better than one large one.

What temperature and humidity should the tent have?

The main job of the exhaust is to keep these values stable. Measure at plant height, for example with a thermometer/hygrometer with two measuring points.

PhaseTemperatureRelative humidity
Seedlings20 to 25 °C60 to 70%
Vegetative growth20 to 28 °C during the day50 to 70%
Flowering18 to 26 °C40 to 50%
Late flowering18 to 24 °C30 to 40%

The sources differ in details; the ranges summarise them. In general: permanently above 28 °C and very dry air below 40% favour pests such as spider mites, while very humid air in dense canopies favours mould.

Does the exhaust keep running at night?

Yes, but turned down. After the lamp switches off, humidity often rises. Let the exhaust run on the normal setting for the first one to two hours of the dark period and turn it down afterwards, but never switch it off completely. A timer or a climate controller does this for you. Our exhaust kits are also available with an app climate controller that regulates the fan according to temperature and humidity. For larger setups, the controllers from GrowControl are a good fit.

Common mistakes: what often goes wrong with exhaust?

  • Fan too small: On paper it is enough, but no longer with filter and ducting. Better to choose a larger one and turn it down.
  • Filter too small: Slows the fan and lets odours through. Choose a filter at least as strong as the fan.
  • Long ducts with many bends: Every bend costs performance. Keep ducting short and straight.
  • Exhaust at the bottom, intake at the top: Warm air rises and has to leave at the top.
  • Switched off completely at night: Humidity rises, and condensation can form on cool walls.
  • No circulation fan: Without air movement in the tent, humid corners develop.
  • Filter never replaced: A spent or clogged filter reduces performance and lets odours through. Replace it according to the manufacturer's instructions.

In our shop at Lorenzstraße 9 in Hof, we have the exhaust kits and fans from Prima Klima, Can-Fan and CarbonActive in stock and will work out with you what suits your tent. Online you will find everything under Climate control, kits under Ventilation kits and ducting under Air ducts.

Featured in this guide

Frequently asked questions

Why should the fan be stronger than the calculation suggests?

The manufacturer's rating usually applies without filter and ducting. A carbon filter, duct length, bends and the heat of the lamp all cost performance. A stronger fan with a speed controller has reserves and runs more quietly when turned down.

Does the carbon filter go before or after the fan?

Before it. The fan pulls the air through the filter. This way the filter works evenly and the fan housing stays clean. The filter hangs at the top of the tent.

Does the filter need the same m³/h rating as the fan?

At least the same, ideally a little more. A filter that is too small slows the fan down and lets odours through because the air flows through the carbon too quickly. Also make sure the flange diameters match.

Are the openings in the tent enough for intake air?

For small tents up to about one square metre usually yes, as long as they are at the bottom on the side opposite the exhaust. Larger setups get their own intake fan.

Should the exhaust run at night?

Yes, turned down. Humidity often rises in the first one to two hours after lights-out, so keep it on the normal setting for that time and turn it down afterwards. You should not switch it off completely.

Sources

All information to the best of our knowledge and based on manufacturer data as of the date shown. It does not replace the manufacturer’s instructions. This guide was created with AI assistance and reviewed by our team.

More from Plant tents & equipment