Harvesting & storage 6 min read

Cleaning, oiling and sharpening harvest scissors

Remove resin with cold, isopropyl alcohol or oil, oil the spring and pivot, sharpen on the bevel and store dry. With a table covering stainless steel, carbon steel and coated scissors.

Resin comes off the blade most easily if you remove it on the same day: put the scissors in the freezer for 10 to 15 minutes, scrape off the coarse residue and then soak the blades for 15 to 30 minutes in isopropyl alcohol or loosen it with oil. Then dry them thoroughly and put a drop of oil on the pivot and spring so that nothing rusts and the scissors close easily. Only the ground side of the cutting edge is sharpened; according to Felco, the bevel is usually 23 to 25 degrees. Stainless steel is easy to care for, carbon steel gets sharper but rusts more quickly; a titanium coating makes it harder for resin to stick.

What gets resin off the blade?

Plant resin hardly dissolves in water, but it does in alcohol and in oil. It is easiest while the residue is fresh. This is how to proceed after a trimming session:

  1. Use the cold: Put the scissors in the freezer for 10 to 15 minutes. According to Zamnesia, this makes the resin firm and easier to scrape off.
  2. Scrape off roughly: Carefully lift off the residue with a blade or a wooden spatula, always away from your body and not across the cutting edge.
  3. Soak: Stand the blades in isopropyl alcohol so that they are completely covered; Zamnesia gives 15 to 30 minutes. Avoid immersing plastic and rubber handles if possible. Felco names 70 per cent isopropyl alcohol for disinfecting the cutting edges.
  4. Wipe and brush: Remove loosened residue with a cloth or a soft brush, including around the pivot.
  5. Dry: Dry the blades thoroughly and leave the scissors lying open until the pivot is dry as well. According to Felco, only oil once the blade is completely dry.
  6. Oil: A drop of oil on the pivot and spring, a thin film on the blades.

Without alcohol, oil also works: Gartenjournal recommends applying penetrating oil to resinous areas, leaving it to work for a few minutes and removing the loosened resin with the rough side of a sponge. Zamnesia describes a paste of coconut oil, bicarbonate of soda and citrus oil. Wipe technical oils off thoroughly afterwards, before the scissors touch plants again.

How do I care for the spring and pivot?

Most harvest scissors have an opening spring that pushes the blades open again after every cut, and a lock for storage. Both collect resin, which makes the movement sluggish. Felco names three points you should check at every thorough clean:

  • Pivot screw: tight but smooth-running. The blades should glide past each other without play and without scraping.
  • Blades: They must meet without a gap. A visible gap means that the scissors crush instead of cutting.
  • Spring: It should compress and open again evenly. If it sticks, there is usually resin between the coils.

A drop of oil is enough for the pivot; then open and close the scissors a few times. Many branded scissors can be taken apart for a thorough clean; on inexpensive spring-loaded scissors the pivot is often riveted, in which case you clean it assembled.

Stainless, carbon or titanium-coated: what needs which care?

Scissor typeBladeStrengthCareIn our range
Spring-loaded scissors, straight bladestainless steelprecise cuts in fine spotsloosen resin after use, dry, oil the pivotHarvest scissors “Straight”
Spring-loaded scissors, curved bladestainless steelgets around curves and into tight areasas for the straight blade, mind the curve when wipingHarvest scissors “Curved”
Topiary shears, slimstainless steel, 24 cm, 160 glight, for delicate workas aboveRomberg “Bonsai”
Carbon steel scissorscarbon steelvery sharp, easy to resharpenwipe and oil thinly after every use, otherwise it rustscurrently not in the online shop, ask in the shop
Coated scissorsstainless steel with a titanium or non-stick coatingresin sticks lessno abrasive cleaners, resharpen the edge gentlycurrently not in the online shop, ask in the shop
Bud trimmer with crankrotating steel bladefor larger quantitiesclean the blade and grid after every usecurrently not in the online shop, ask in the shop

Stainless steel forgives you if the scissors are occasionally left damp. According to Bloomist, carbon steel is harder, holds a sharper edge and is easier to resharpen. However, it needs care after every use: wipe it and rub it thinly with camellia oil. A dark patina is normal on carbon steel, rust is not. Titanium-coated scissors usually means a thin layer of titanium nitride on stainless steel, not a blade made of titanium. The coating is meant to stop sticky material from adhering. When resharpening, you inevitably wear it away at the cutting edge, so grind only as little as necessary and do not treat the coating with steel wool.

How do I sharpen harvest scissors?

Clean first, then sharpen: according to Felco, you should never grind a dirty blade, because otherwise you cannot see the bevel clearly. On scissors whose blades cut past each other, like harvest scissors, only the side with the bevel is ground.

  1. Find the bevel: The angled, shiny surface on the cutting edge is the side you sharpen. The flat inner side stays flat.
  2. Follow the angle: Place the stone against the existing bevel instead of measuring an angle. Felco gives usually 23 to 25 degrees from the factory, Bloomist 20 to 30 degrees.
  3. Draw in one direction: According to Felco, from the base of the blade to the tip, 5 to 10 strokes with even pressure, not back and forth.
  4. Remove the burr: Lay a fine stone flat on the back and remove the burr with a light stroke, without grinding a new bevel there.
  5. Test and oil: A sheet of paper should be cut cleanly. Then oil the pivot and spring.

The sources differ here: Gartenjournal says to grind both cutting edges on bypass scissors, whereas Felco grinds only the cutting blade on its bevel. On spring-loaded scissors with two identical blades, you grind each one only on its own bevel. According to Felco, a quick touch-up is enough when cutting gets harder, and a thorough service at least once a season.

How do I store the scissors properly?

  • Dry and airy: Felco advises a dry place, ideally hanging. For long breaks, silica gel sachets help.
  • No leather or fabric case: According to Bloomist, they hold moisture against the blade. A guard for the tip is still sensible.
  • Lock closed: When closed, the tip is protected and the spring is relieved.
  • Over the winter: Gartenjournal recommends wrapping the oiled scissors in an oily rag.

Store them separately from the drying material: you can read how to dry and store the harvest itself in Drying properly and Storing without mould.

When is it worth getting new scissors?

According to Bloomist, light surface rust can be removed with fine steel wool of grade 000 or 0000, then dry and oil. You should replace scissors if the blade has deep rust pits, if the blades no longer meet without a gap even after adjustment, if the tip is bent or if the coating flakes off over large areas. For branded scissors such as Felco, replacement blades and springs are available. With inexpensive spring-loaded scissors, a new pair is usually simpler than regrinding.

Common mistakes: what often goes wrong when caring for scissors?

  • Letting resin dry on overnight: Fresh resin comes off much more easily than hardened residue.
  • Bathing the whole scissors in alcohol: Plastic and rubber handles can suffer. Only immerse the blades.
  • Put away wet: Residual moisture in the pivot leads to rust, especially on carbon steel.
  • Never oiled: Without oil, the pivot becomes stiff and the spring has to work against resistance.
  • Grinding the flat side: Then the blades no longer meet cleanly and the scissors crush.
  • Treating the coating with steel wool: The layer gets scratched and loses its non-stick effect.

In our shop at Lorenzstraße 9 in Hof, you can hold our harvest scissors with straight and curved blades and the Romberg topiary shears in your hand and ask which other scissors and trimmers we have in stock. Online you will find scissors and drying nets under Cutting & drying.

Featured in this guide

Frequently asked questions

Which isopropyl alcohol should I use for the scissors?

Felco names 70 per cent isopropyl alcohol for disinfecting the cutting edges. More highly concentrated alcohol contains less water, which helps when loosening resin. Above all, it is important that the blades are completely covered and the handles stay out as far as possible.

Can I keep the scissors clean while I work?

Yes, you can wipe the blades in between with a cloth lightly soaked in alcohol or oil. Some people keep a second pair ready and switch as soon as the first one gets sticky. This does not replace a thorough clean.

Do stainless steel scissors never rust?

Stainless steel is very resilient, but not invulnerable. If moisture and plant residue remain in the pivot, surface rust can form there. Drying and a drop of oil prevent this.

Do I need to sharpen inexpensive spring-loaded scissors at all?

Resharpening is possible, but is often hardly worthwhile with very inexpensive scissors. If the blades no longer meet without a gap or the tip is bent, a new pair is usually the simpler solution.

Which oil is suitable for the pivot?

For carbon steel, Bloomist names camellia oil; Felco uses its own care spray and grease for the pivot and spring. Gartenjournal names all-purpose or cooking oil. Use only a little and wipe off excess oil before the scissors touch plants again.

Sources

All information to the best of our knowledge and based on manufacturer data as of the date shown. It does not replace the manufacturer’s instructions. This guide was created with AI assistance and reviewed by our team.

More from Harvesting & storage